V2.01.001 :	Support W55FA93 with SD booting USB firmware
V2.01.002 :	Add musb.bin to support W55FA91 and fix some 
		low USB performance desktop may connect W55FA91 fail issue
V2.01.003 :	Fix V2.01.002 still use 16 bytes file name to access W55FA93 issue
V2.01.004 :	Add FA93_musb.bin to support W55FA93 ver C,
		the W55FA93 ver C does not need SD boot disk
v2.01.005 :	Fix the negative capacity issue
                Change SDHC Frequency from 50MHz to 24MHz
v2.01.006 :	Fix unable to specify the Image execute address of Logo in SD card option
v2.01.007 :	Support "Enable SD format" option for SD solution
v2.01.008 :	Support SD port 0/1/2 operations
		Support display SPI flash size
		Fix Turbowriter SPI add Logo issue (Logo execute address can't be set)
v2.01.011 :	For VA91/VA93/FA95 and Fix SPI(Raw data) issue
		Fix SPI(Raw data) issue - Turbowriter sends Boot code header every 64KB.
		FA95 Turbowriter 1st version
		User can add Optional marker in Boot Header by adding information in TurboWriter.ini.  
		User can let IBR to set Value to Register when USB Booting by adding information in TurboWriter.ini. 
		Ex: Set Register 0xB0003000 to 0x00130456	
			[USER_DEFINE]
 			 B0003000 = 00130456
v2.10.001 :	Modify connect flow for FA95C 
v2.10.002 :	Fix the MakeROM function for FA93/95
		Add new function in SPI(Raw Data) - Read back from SPI	
		Using SPIFLASH ID.ini function to support the SPI flash that not support (Size unit is KB)
v2.10.003 :	Fix Turbowriter firmware size limitation
v2.20.001 :	Support N3290xE & N3290xF

[FA93]
2010/12/08-V01: Fix wrong booting marker in block 0
2010/12/28-V01: Support Samsung K9F8G08U0M (1GB with SLC 4K page) NAND chip
2011/01/03-V02: Fix change to SD card detect error issue
		Change USB control flow to fix USB booting sometimes connect TurboWriter fail issue
2011/03/07-V01: Fix unable to specify the Image execute address of Logo in SD card option
2011/03/21-V01: Fix erase system area fail if there is no reserved area setting
2011/06/15-V01: Support H27UAG8T2A 4K page Nand
2011/07/06-V01: Support "Enable SD format" option for SD solution
2011/08/19-V01: Support SD port 0/1/2 operations
		Support display SPI flash size
		Fix long NAND option response time if without NAND flash
		Fix Turbowriter SPI add Logo issue (Logo execute address can't be set)
2011/10/28-V01: Fix SDRAM - Download and run issue
2012/05/10-V01: Fix H27UAG8T2ATR Verify error issue
		Fix MLC NAND flash writing sequence issue
2012/06/13-v01: Support MXIC MX25L25635E SPI flash
		Fix SPI flash issue when Turbowriter can't calculate the spi flash size.
2012/07/10-v01: Support 4-Byte Address mode for SPI flash larger than 16MB
		Support FA93QDN	& FA93SDN
2012/07/11-v01: Change Turbowriter executing address to 4MB
2012/09/25-v01: Support GigaDevice SPI flash
2013/01/30-v01: Fix the issue that can't see the SPI image list
2013/03/04-v05: Fix the issue that can't see the SPI image list
2013/03/14-v05: Using SPIFLASH ID.ini function to support the SPI flash that not support (Size unit is KB)
		[ID]		[SIZE]	
		C84017		8192
2013/03/25-v05: Fix SD set system area bug (Write operation doesn't work when image list exists and system area value is default value - 0xFFFFFFFF)
2013/03/26-v05: Keep Clock setting from IBR (Remove Clock init function)
2013/05/08-v05: Modify SPI flash Read/Write unit from Byte to Word
2013/07/12-v05: Fix SD issue (Sometimes SD card is formated when SD card is first time written by Turbowriter)

Notice: If you want to fix the USB transfer speed in FullSpeed mode, please rename the file 
	FA93_musb_FullSpeed.bin to FA93_musb.bin and replace the origrinal one.


[FA95]
2012/01/16-V01: FA95 Turbowriter firmware 1st version (FA95_musb.bin & FA95_musb_FullSpeed.bin)
2012/01/20-V01: Support Hynix NAND H27UAG8T2B(H27UAG8T2BTR)
2012/04/06-V01: Support 4KB page size with BCH T24 NAND flash.
		Support new NAND flash Micron MT29F16G08CBACA/MT29F32G08CBACA.
		Change BCH from T8 to T24 for NAND flash Micron MT29F16G08CBACA/MT29F32G08CBACA.
		Fix H27UAG8T2ATR Verify error issue
		Fix MLC NAND flash writing sequence issue
2012/04/11-V01: Add T24 BCH correct data function
2012/05/10-V01: Fix long time for USB Connection issue 
		Fix Remaining MLC NAND flash writing sequence issue	
2012/06/13-v01: Support MXIC MX25L25635E SPI flash
		Fix SPI flash issue when Turbowriter can't calculate the spi flash size.
2012/07/10-v01: Support 4-Byte Address mode for SPI flash larger than 16MB
2012/08/28-v01: Fix Wrong NAND Disk size issue when using NAND ID.ini function
2013/03/04-v01: Fix the issue that can't see the SPI image list & Support GigaDevice SPI flash
2013/03/14-v01: Using SPIFLASH ID.ini function to support the SPI flash that not support (Size unit is KB)
		[ID]		[SIZE]	
		C84017		8192
2013/03/25-v01: Fix SD set system area bug (Write operation doesn't work when image list exists and system area value is default value - 0xFFFFFFFF)
2013/05/08-v01: Fix SD port 2 fail issue
		Modify SPI flash Read/Write unit from Byte to Word
2013/07/12-v01: Fix SD issue (Sometimes SD card is formated when SD card is first time written by Turbowriter)

Notice: If you want to fix the USB transfer speed in FullSpeed mode, please rename the file 
	FA95_musb_FullSpeed.bin to FA95_musb.bin and replace the origrinal one.

